Digital multimeter circuit using ICL7107

I am showing you a digital multimeter circuit using ICL7107.

We modify them from a normal DC digital voltage meter circuit to smart multimeter. It is so versatile available function.

For example, Measure DC voltage, ACV, DC Amp meter, AC Amp meter and as the Ohms meter, etc.

Try to build this project to use it really worth and fully enjoy.

Thanks, Photo from the AstroAI Digital Multimeter. Why is a good tool? You can get an answer from here.

5 Special Features

• 1. DC Voltage: 200mV, 2V, 20V, 200V, 2KV, 20KV
• 2. AC Voltage: 200mV, 2V, 20V, 200V, 2KV, 20KV
• 3. DC Amp: 200uA, 2mA, 20mA, 2A, 10A
• 4. AC Amp: 200uA, 2mA, 20mA, 2A, 10A
• 5. Ohms meter: 200, 2K, 20K, 200K, 2M, 20M

Function 1: Digital DC voltmeter circuit

In Figure 1: the schematic diagram of this project. Of course, the easiest way is used as the DC voltage meter circuit.

Figure1: DC voltage measurement circuit

The original characteristics of this circuit can measure voltages up to 200 mV only.

However, we can apply it to measure the voltage range higher with a few input resistors. See in Table 1:

Table 1 is shown in the resistance at various ranges.

Note:

We may choose resistors in both formats.

For the too high voltage measurement. It is necessary to use the external high voltage probe.

R3 = 100K; R4 = 10K

Function 2: DC ampere meter circuit

Next, take a look at the simple digital DC ampere meter circuit. The appropriate designing, determine with resistance in parallel on the input of voltmeter.

The main principle to calculate.

The resistance is the voltage caused by the flow of current through the resistor. In each range is maximum up to 200mV.

As shown circuit diagram below.

Figure 2: DC Ammeter circuit

See the circuit in Figure 2. Designing having a range of up to 5 range.

For the high current measurement 2 Amperes. You should separate it fro other input. Because the contact of switch that can not withstand currents.

Diode D1 and D2 are overload protection to provide the input.

Note: R2 = 90 ohms, R3 = 9 ohms

Function 3: AC voltage measurement

We can design the AC voltage measurement circuit. By adding the AC to DC converter circuit. They have a relationship together. As shown in Figure 3.

Figure 3:  Digital AC voltmeter circuit without transformer

The AC voltage is measured to reduce voltage same the DC voltmeter circuit. Then, enter to the AC to DC converter circuit by IC1 and accessories in Figure 3.

Adjust VR1 to tune a correct voltage reading.

Function 4: AC Ammeter Circuit

The same principle applies to the DC voltmeter circuit. We can be applied to the AC ammeter by adding the AC to DC converter before as shown in Figure 4

Figure 4:  AC Ammeter measurement

Function 5: Ohms meter

The advantaged of this digital multimeter better than a regular meter:

This can read accurately. And can measure the resistance of 0.1 ohms or less. And higher as 10M easily.

With circuit connecting as shown in Figure 5.

Figure 5 the ohms meter circuit

Figure 6 the ICL7107 module

The digital meter module in Figure 1-5 Show legs of ICL7107.
Compared to the legs of the modules to Easy to write all the circuits. The ROH pin is the output reference voltage at a middle leg of the horseshoe-shaped resistor.

Figure 7: Full  a digital multimeter circuit diagram

Here is a full circuit that works perfectly.

Parts you will needs

• IC1: TL071, Operational Amplifiers – Op Amps JFET Input Low Noise
• IC5: LM7805, Standard Regulator 5 Volt 1 Amp 3 Pin 3+ Tab TO-220
• IC3: CD4049, CMOS Hex Inverting Buffer/Converter
• IC2: CD4066, Quad Analog Switch/Multiplexer/Demultiplexer
• IC4: ICL7107 or ICL7106, Analog to Digital Converter Single Dual Slope 0.003k SPS 3 1/2 Digit LED 40-Pin PDIP
• LED 7 segment or LCD display

More Switches please read in a text

0.5W Resistors tolerance: 1%

• R1, R26: 10M
• R2, R25, R30, R33, R36, R38: 1M
• R3, R15, R24: 100K
• R4, R19, R20, R23: 10K
• R5, R22: 1K
• R6: 110 ohms
• R7: 1K
• R8: 100 ohms
• R9: 10 ohms
• R10: 1 ohm 1 watt
• R11, R12, R13, R14: 0.1 ohms 2 watts
• R16: 3.3K
• R17, R27: 2.2K
• R21: 100 ohms
• R28: 270 ohms
• R29: 47K
• R32: 5K

MKT capacitors

• C14: 33pF 63V
• C15: 330pF 63V
• C16: 0.0039uF 63V
• C11: 100pF 63V
• C10: 0.1uF 63V
• C9: 0.01uF 63V
• C8: 0.47uF 63V
• C7: 0.22uF 63V

• Electrolytic capacitors
• C5, C6: 470uF 16V
• C13: 10uF 16V

Diodes

• D1-D4: 1N5408
• D7, D8, D9, D10: 1N4001
• D5, D6, D11, D12, D13, D14, D15: 1N4148

Switch see in circuit and PCB layout

Digital voltmeter circuit »

Related Posts

Apichet Garaipoom

I love electronics. I have been learning about them through creating simple electronic circuits or small projects. And now I am also having my children do the same. Nevertheless, I hope you found the experiences we shared on this site useful and fulfilling.